SLP-4132C-81 no.6060 1/4 features gaasp yellow led 5.0mm?, round top type lamp clear yellow resin package type the insertion which made it stick to pcb is possible high luminous intensity, high reliability and long life application : for the general public welfare absolute maximum ratings at ta=25 c (as per jis c 7032) parameter symbol rating unit forward current * 1 i f 25 ma pulse forward current * 2 i fp 100 ma reverse voltage v r 3v power dissipation p d 70 mw operating temperature topr --25 to +80 c storage temperature tstg --30 to +85 c soldering temperature * 3 tsol 260 c * 1 see forward current derating * 2 pulse width = max. 10ms duty ratio = max. 1 / 10 * 3 max. 5sec., lead soldering condition : min. 1.6mm from case (used 1.6mmt pcb) electrical / optical characteristics at ta=25 c parameter symbol conditions min. typ. max. unit foward voltage v f i f = 20ma 1.7 2.1 2.8 v reverse current i r v r = 3v -- -- 10 m a luminous intensity * 4 i v i f = 20ma 20 50 -- mcd peak wave length l p i f = 20ma 575 585 595 nm line half width dl i f = 20ma -- 40 -- nm capacitance c o v o = 0 f = 1mhz -- 40 -- pf response time t -- -- 90 -- ns * 4 luminous intensity is measured by j-16 (sony tektronix) of which our office possess. note use a unit as one sack. sanyo electric co.,ltd. semiconductor company tokyo office tokyo bldg., 1-10, 1 chome, ueno, taito-ku, tokyo, 110-8534 japan ordering number : en6060 SLP-4132C-81 infrared led ?5mm yellow contact type led lamp 52699 gi, ( mi ) 5.4 0.4 5.8 0.4 0.5 ? ?.8 7.3 0.5 0.8 max 11.5 0.5 30.8 1 (2.5) (1.5) 7.0 anode cathode note : material -- lron coating -- solder lead center off : 0.4 unit : mm 2 max (not soldered)
SLP-4132C-81 no.6060 2/4 typical characteristics these shows the electrical and optical characteristics of this products, and not assure this dispersive contents. caution forward current vs. forward voltage forward current (ma) forward voltage (v) intensity vs. temperature (i f : constant) relative intensity temperature ( c) intensity vs. current relative intensity forward current (ma) spectrum relative intensity wave length (nm) forward current derating (abusolute maximum rating) forward current (ma) temperature ( c) directivity 30 20 10 5 3 2 1 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 1.5 1.0 0.5 --40 --20 0 20 40 60 80 100 5 10 2 1 0.5 0.2 0.1 1 2 5 10 20 50 100 200 30 35 25 20 15 10 5 0 102030405060708090100 90 80 70 60 50 40 30 20 10 0 10 20 30 40 50 60 70 80 90 1.0 0.5 0.1 1.0 0.5 0 500 550 600 650 700
SLP-4132C-81 no.6060 3/4 (1) bending a lead should avoid not to cause chip deterioration or so. when bending is necessary, care must be taken considering the following points : q bending a lead must be done before soldering. w bending a lead must be done in the states of fixing a lead tight and applying no stress on the resin part; otherwise it may cause troubles such as gold wire breaking. e a lead must be bent at intervals of 1.6mm from the edge of the resin part. r do not bend the same portion of lead more than twice. (2) setting a product by a tool such as holder should avoid. when necessary, no stress should be applied to the resin part and lead by sufficient considerations on dimension tolerance, thermal expansion, thermal contraction of holder, product and circuit board. (3) the hole pitch of a circuit board must fit to its lead pitch. (4) when soldering, care must be taken considering the following points : q do not heat a product under any stress (ex. : twist) to leads. w do not heat (by soldering, for example) a product in the states of being forced to the resin part. (5) do not use the flux containing chlorine which may cause corrosion of lead and washing is preferable. when washing is necessary, avoid washing the whole product and wash only the needed part under the following conditions. ? chemicals : methyl alcohol ? temperature : 45 c max. ? time : 30sec. max. precautions
SLP-4132C-81 no.6060 4/4 caution 1. no products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster / crime-prevention equipment or the like, and the failure of which may directly or indirectly cause injury, death or property loss. 2. anyone purchasing any products described or contained herein for an above-mentioned use shall: 1) accept full responsibility and indemnify and defend sanyo electric co.,ltd., its affiliates, subsidiaries and distributors or any of their officers and employees, jointly and severally, against any and all claims and litigation and all damages, costs and expenses associated with such use. 2) not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on sanyo electric co., ltd., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. 3. information (including circuit diagrams and circuit parameters) disclosed herein is for example only; it is not guaranteed for mass production, sanyo believes the information disclosed herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. precautionary instructions in handling gallium arsenic products special precautions must be taken in handling this product because it contains, gallium arsenic, which is designated as a toxic substance by law. be sure to adhere strictly to all applicable laws and regulations enacted for this substance, particularly when it comes to disposal. manufactured by ; tottori sanyo electric co., ltd. led division 5-318, tachikawa-cho, tottori city, 680-8634 japan tel: +81-857-21-2137 fax: +81-857-21-2161 ps
|
